I will say that it takes a gentler hand to use these than other types of clip-ons, since you are basically flexing the plastic to open it enough to slide onto your earlobe…and if I had been a little rougher, I think I could have easily snapped them in half in the process! After I got them on, both stud and dangle style earrings held up quite well to normal everyday wear (including walking outdoors, driving, taking public transit, and putting on / taking off a backpack), and neither of them threatened to fall off on their own at any point throughout the day. It took a bit of practice to get the earrings on because the findings were so small and thin and I was also afraid of breaking the plastic, but I got the hang of it pretty quickly. ![]() Thankfully, after a couple of minutes, the glue was set enough that I could put the earrings down and let them fully dry overnight without further work on my part. This part was slightly tricky because the earring could start tilting in any direction while the glue was drying, so I kept finding that they looked crooked from different angles and had to make frequent adjustments. Because the area to glue is so small, I find that either using this method or using a toothpick to transfer glue onto the gluing surface yields a cleaner result than trying to squeeze glue directly on from the tube.įrom there, I just pressed the part of the earring that used to have the post onto the finding, doing my best to keep it aligned until the glue dried enough to hold it. ![]() Also, because of how hard the posts were, they actually nicked the blades of my wire cutters □ – in the future, I’ll probably look for some heavier-duty cutters to use for this purpose.Īfter removing the posts, I squeezed a dab of E6000 onto some scrap paper and dipped the resin finding in to get a small amount of glue on it. It might help to cut them in a box to help contain the flying metal. I’m not sure if all posts are made with similar strength, but those posts were harder than I expected! They flew and ricocheted everywhere when I cut them, so I’d definitely recommend taking some safety precautions with this, especially if you have kids or pets running around. The first thing I did was cut the posts off of the earrings with my jewelry wire cutters. The actual process of converting the earrings was quite quick and simple, but I did learn a few things along the way as well. The other variations are exactly the same as the plain findings, aside from the added pieces. There are also ones that have pre-attached pieces (such as chains), but for the purposes of converting pre-made earrings, I thought the plain ones would work best. The Processįor this review, I only tested out the plain findings. I’ll update when I get a chance to try ones from any other sources!Īfter getting back home, I got a pair of longer dangling earrings as well as some small studs to put my new findings to the test. For those of you who don’t have easy access to a local store that stocks these, I also found plenty of them on Etsy – but I don’t know if they’re all made the same, so I don’t know for sure this review will be accurate to those as well. ![]() Sure enough, Yuzawaya had them (made by Munsell, according to the package) and even stocked a few variations, so I got some different ones to test out. I find that Asia in general tends to be more friendly to non-pierced ears and, therefore, clip-on findings tend to be more commonly found there, so I made a point to look for these specific types of findings at Yuzawaya in Tokyo while we were there in December. I was admittedly not super sold on using a finding made out of plastic instead of metal, but I had to try it out…for science! This shape makes it possible to simulate either a stud or a dangle earring. These are basically small split rings made out of clear, semi-flexible plastic, with a small protrusion on one side where a design element can be attached. I was intrigued (but skeptical, to be honest!) when I recently came across a new type of clip-on finding: “invisible” resin clip-ons, sometimes also referred to as “omega” clip-ons due to their shape.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |